"I have just installed my new cushions and I\u2019m so excited!\n\nInstallation was a BREEZE. Be careful when detaching the old cushions because you may scratch the headset paint with the knife. I almost did that. \ud83d\ude2c\n\nInsert the knife very carefully, the more \u201clength\u201d you slide in, the easier and gentler it\u2019ll be to pop up the cushion. Inserting just the tip of the knife requires more force\/pressure to lift the cushion and unglue it, and this is how you\u2019ll scratch the sides of your headset.\n\nMake sure you remove the \u201cmetal\u201d piece (in my pics it\u2019s the black ring on the old cushions). Otherwise your new cushions will not be placed properly and will look separated from the headset (thanks to another review I was aware of this!).\n\nRemove ALL the glue that\u2019s there. If it\u2019s still sticky, it needs to be cleaned. The alcohol wipe wasn\u2019t enough for removing it, but it definitely helped with the small pieces of glue. For the big ones like on one of the photos, simply lift one end of the glue strip and peel it all off at once (knife helps to lift the ends of the glue!).\n\nWipe it off again. Attaching the cushions is easy! Right side is different than the left; it has an indentation where you insert the cable into the headset - pretty easy to see it. There are pins on the headset, they\u2019ll go into the holes on the cushions. Play with it a bit before doing it for real, so you make sure which holes are the correct ones (not all will be used).\n\nGENTLY lift the sticker backing with the tip of a knife (very gently... I almost ruined it!) and align the pins with the holes, put pressure all around and voil\u00e0! \ud83d\udc4c\ud83c\udffb It\u2019s REALLY easy. The instructions are very clear.\n\nIt looks really good! I don\u2019t know how long it\u2019ll last, but I will update that whenever I know."

"I have just installed my new cushions and I\u2019m so excited!\n\nInstallation was a BREEZE. Be careful when detaching the old cushions because you may scratch the headset paint with the knife. I almost did that. \ud83d\ude2c\n\nInsert the knife very carefully, the more \u201clength\u201d you slide in, the easier and gentler it\u2019ll be to pop up the cushion. Inserting just the tip of the knife requires more force\/pressure to lift the cushion and unglue it, and this is how you\u2019ll scratch the sides of your headset.\n\nMake sure you remove the \u201cmetal\u201d piece (in my pics it\u2019s the black ring on the old cushions). Otherwise your new cushions will not be placed properly and will look separated from the headset (thanks to another review I was aware of this!).\n\nRemove ALL the glue that\u2019s there. If it\u2019s still sticky, it needs to be cleaned. The alcohol wipe wasn\u2019t enough for removing it, but it definitely helped with the small pieces of glue. For the big ones like on one of the photos, simply lift one end of the glue strip and peel it all off at once (knife helps to lift the ends of the glue!).\n\nWipe it off again. Attaching the cushions is easy! Right side is different than the left; it has an indentation where you insert the cable into the headset - pretty easy to see it. There are pins on the headset, they\u2019ll go into the holes on the cushions. Play with it a bit before doing it for real, so you make sure which holes are the correct ones (not all will be used).\n\nGENTLY lift the sticker backing with the tip of a knife (very gently... I almost ruined it!) and align the pins with the holes, put pressure all around and voil\u00e0! \ud83d\udc4c\ud83c\udffb It\u2019s REALLY easy. The instructions are very clear.\n\nIt looks really good! I don\u2019t know how long it\u2019ll last, but I will update that whenever I know."