EGW Colt Gold Cup, Python, Anaconda Sight Mount (fits Burris FastFire, Docter, Viridian RFX25) Reviews

4.7 Rating 6 Reviews

HAVE AN AIMPOINT ACRO? USE THIS PLATE TO ADAPT THE DOCTOR FOOTPRINT TO THE AIMPOINT ACRO FOOTPRINT
This mount fits:
Colt Gold Cup Colt Trooper Mark 3 Colt Python (does NOT fit 2020 and newer models) Colt Anaconda (does NOT fit 2020 and newer models)*
This is for Colt models with the Elliason style adjustable rear sight. Specifications Material: 7075 AluminumCoating: Matte Black HardcoatOverall Length: 1.811"Overall Width: .99"Torque Specs: 15 in/lbs Mounting Hardware:(2) 6-32 Button Head Screws(2) 6-32 Flat Head Screws(1) 6-32 Set Screw Red Dot Fitment:
Viridian RFX25
Vortex Viper
Vortex Venom ( Not Enclosed )
Burris FastFire
Burris FastFire 2
Burris FastFire 3
Burris FastFire 4
Docter
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot
Cuda RX-795
Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.Installation Instructions- Remove the rear sight*- Install the EGW Sight Mount in the dovetail- Tighten set screw (if applicable)- Place the red dot sight on the EGW Sight Mount(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)- Apply blue Loctite to the provided mounting screws- Torque mounting screws to 15in/lbs2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights2 Flat Head Cap Screws - Provided for Burris FastFire and Docter SightsThe screws that are included with this mount require a 5/64'' allen wrench for installation.Click here to see a video from Vortex on how to install our red dot base on a slide.
WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH. Modification of your firearm may nullify the manufacturer's warranty.This product should be installed and checked by a qualified gunsmith.No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.

Alt Description
Colt Gold Cup Vortex Venom Red Dot Mount Colt Trooper Mark 3 Vortex Venom Red Dot Mount Colt Python Vortex Venom Red Dot Mount Colt Anaconda Vortex Venom Red Dot Mount

Visit Product Page

Location:

52 BELMONT AVE,
QUAKERTOWN
Pennsylvania
18951

Visit Product Page

“I had a bit of fitting to do, but it worked out.”

Helpful Report

Posted 8 months ago

“Fits great! Old guy eyes can’t see irons.”

Helpful Report

Posted 1 year ago

“Fit was perfect and delivery and customer service stellar. Minor hiccup on the correct part number to order but customer service handled resolution very quickly”

Helpful Report

Posted 1 year ago

“Mount was missing elevation screw but issue was addressed immediately. Thanks”

Helpful Report

Posted 2 years ago

“Re: Colt Gold Cup Pistol, EGW SKU #49322, Vortex Venom Sight. With this setup, my impacts were 13" low at 25 yards. I was advised to install a 1 degree shim between the mount and the sight. Doing so would then physically shift the sight in such a way that it would be pointing closer to where the impacts were on the target. With the shim in position, it completely covered the two rear integral pins on the mount, in effect negating their purpose. The two front pins did protrude above the shim, but only by a very small amount. I was not comfortable installing the Venom onto the mount with this arrangement as it was, especially when considering that this is a .45 ACP Pistol. The shim was removed and the sight was attached directly onto the mount. To obtain a "zero", almost all of the available, upward elevation in the sight had to be used. I don't like to "ride on the edge" of any sight's range of adjustment, but no other option is available. The four holes in the underside of the Venom are approximately 3/32" deep. The four integral pins on the mount are only 1/32" high. If these pins were made higher than they are, all of them would always be able to engage the four holes in the bottom of the sight, whether a shim was being used or not. This mount is very well made, except for the height of its pins.”