Holosun K Series (fits Vortex Defender Series, Shield RMSC/RMS/SMS, Leupold DeltaPoint Pro) Mount for Kimber 1911 Fixed Reviews

4.4 Rating 22 Reviews

Mounting Hardware is Included WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH. This Mount Fits:
Kimber 1911's with Fixed Rear Sights Desert Eagle 1911G* Desert Eagle 1911C*
This mount does not fit:
Kimber Micro Kimber Micro 9
*This mount will require a decent amount of fitting to work with the Desert Eagles and is NOT a drop in part on that application.* Material: 7075 AluminumCoating: Matte Black HardcoatOverall Length: 1.604"Overall Width: .99"Mounting Hardware: (2) 6-32 Button Head Screws, (1) 6-32 X 3/16 Set Screw Red Dot Fitment: Vortex Defender Series (Defender XL requires the screws provided by Vortex) Vortex Venom (Enclosed Red Dot) OSight SE Bushnell RXS-100 Crimson Trace CTS-1500 Holosun 407K* Holosun 407k-GR Holosun 507K* Holosun 507k-GR Holosun EPS-GR* Holosun EPS-RD* Holosun EPS-Carry-GR* Holosun EPS-Carry-RD* Jpoint Leupold Delta Point Pro Optima Redfield Accelerator Shield RMS Shield RMSc Shield SMS Sig Romeo Zero
Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.Simply remove the rear sight on your gun and replace it with our mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.Installation Instructions- Remove the rear sight*- Install the EGW Sight Mount in the dovetail- Tighten set screw (if applicable)- Place the red dot sight on the EGW Sight Mount(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)- Apply blue Loctite to the provided mounting screws- Torque mounting screws to 15in/lbs WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH. Modification of your firearm may nullify the manufacturer's warranty.This product should be installed and checked by a qualified gunsmith.No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.

Visit Product Page

Location:

52 BELMONT AVE,
QUAKERTOWN
Pennsylvania
18951

Visit Product Page

“Customer Service identified the correct part that I needed for my Kimber KDS9 classic. The amount I help I received was instrumental and correctly mounting the optic. I cannot recommend them more highly wonderful help.”

Helpful Report

Posted 1 month ago

“works perfect. thanks”

Helpful Report

Posted 3 months ago

“Disappointed, poor fit, required a lot of filing.”

Helpful Report

Posted 4 months ago

“Great product!”

Helpful Report

Posted 5 months ago

“Perfect fit! Easy to put on and works great. Appreciate EGW and the folks there.”

Helpful Report

Posted 5 months ago

“Fit was wonderful. lightweight, seems durable . right in my price range.”

Helpful Report

Posted 6 months ago

“I have a Kimber 1911 with a fixed rear site. I removed the rear site without difficulty. I have a pusher. I did have a problem with the installation of the mount you sent me. I managed to get the mount started in the dovetail with some difficulty. I got it in about half way, or nearly that, and I decided I needed help. It was very tight and I didn’t want to damage anything. I took it to my gunsmith and waited in the front show room while the gunsmith pushed it in. He came back, after some time, and show me the mount that was now destroyed and told me that in the attempt to install the mount he had also damaged his pusher. I don’t think my Kimber slide was damage. I looked at the slide briefly, but I left it with him. I didn’t use Loctite in the attempt to install the mount. I’ve had a little time to think about it and I do believe the problem is with the EGW mount. Assuming that the design of the mount is good, I think the mount was manufactured outside tolerances to the high side, though I have no way of taking measurements. I should have been able to self-install the mount if the mount had been designed and manufactured correctly. I own a Glock 19 Gen 2 that I had self-installed a mount on and I don’t recall having any problems with it. I’m not a gunsmith but I do have some related experience. I’m a retired Airframe Stress Engineer. I’ve work for companies including Lockheed, Boeing, Northrup, Sicorsky, and Gulfstream supporting the design, manufacture, and repair of both civilian and military aircraft. I’ve also worked as a Stress Engineer for Rolls-Royce, Indianapolis supporting design, manufacture, and repair of their gas turbine engines. I’ve left my slide with the gunsmith. He said he would secure another mount and complete the installation. In the mean time I am without my Kimber.”

Helpful Report

Posted 6 months ago

“I brought the part and my Kimber Ultra Carry II to my gunsmith.He really did not want to install the part in the dove tail of the Kimber as he said it would not fit without potentially damaging the part and or the dovetail on the slide. I gave him the OK to try and I would not hold it against him if either was damaged. Ultimately, with a lot of banging the part was put into the dovetail. He told me with all the work involed the part would NOT be able to be removed. I do NOT recommend this installation for the faint of heart....I have yet to fire the UCII with the optic on it....Ultimately, I might love the decision to change over....I can say the part is not going to loosen up. The only question will be how the optic fairs on the UCII.”

Helpful Report

Posted 9 months ago