Holosun K Series (fits Vortex Defender Series, Shield RMSC/RMS/SMS, Leupold DeltaPoint Pro) Mount for GI 1911 Reviews

3.7 Rating 7 Reviews

Mounting Hardware is Included
This mount fits:
1911s with a G.I. style rear sight cut
Springfield 1911A1
Iver Johnson 1911A1
Iver Johnson 1911A1 9
Iver Johnson Falcon 45
Iver Johnson Thrasher 45
Iver Johnson Thrasher 9
Iver Johnson 1911A1 Chrome 38W
Iver Johnson 1911A1 Chrome 38P
Iver Johnson 1911A1 CHRW45
Iver Johnson 1911A1 CHR45P
Iver Johnson 1911A1 CHR45WP
Iver Johnson 1911A1 Zombie
Iver Johnson 1911A1 Copperhead
Iver Johnson 1911A1 Water Moccasin
Iver Johnson 1911A1 Boa
Iver Johnson 1911A1 Muddy Girl 9mm
Iver Johnson 1911A1 Digital Navy
Iver Johnson 1911A1 Digital Snow 45ACP
SAR 2000
Material: 7075 AluminumCoating: Matte Black HardcoatOverall Length: 1.604"Overall Width: .99"Mounting Hardware: (2) 6-32 Button Head Screws, (1) 6-32 X 3/16 Set Screw
Red Dot Fitment:

Vortex Defender Series
OSight SE
Bushnell RXS-100
Crimson Trace CTS-1500
Holosun 407K*
Holosun 407k-GR
Holosun 507K*
Holosun 507k-GR
Holosun EPS-GR*
Holosun EPS-RD*
Holosun EPS-Carry-GR*
Holosun EPS-Carry-RD*
Jpoint
Leupold Delta Point Pro
Optima
Redfield Accelerator
Shield RMS
Shield RMSc
Shield SMS
Sig Romeo Zero
Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.Simply remove the rear sight on your gun and replace it with our mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.Installation Instructions- Remove the rear sight*- Install the EGW Sight Mount in the dovetail- Tighten set screw (if applicable)- Place the red dot sight on the EGW Sight Mount(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)- Apply blue Loctite to the provided mounting screws- Torque mounting screws to 15in/lbs
WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH.
Modification of your firearm may nullify the manufacturer's warranty.This product should be installed and checked by a qualified gunsmith.No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.

Visit Product Page

Location:

52 BELMONT AVE,
QUAKERTOWN
Pennsylvania
18951

Visit Product Page

“Fits perfectly on 1911A1 norinco fixed sights.”

Helpful Report

Posted 4 weeks ago

“Fits perfectly to my Charles Daly 1911 GI and in RMSc foot print. The only issue is the post is too short for romeo zero with metal shield. so you cannot use the metal shield for romeo zero. The post is the same thickness of the metal shield that leaves the romeo zero mounted with only 2 screws without the post stopping. I left out the metal shield and it fits perfectly.”

Helpful Report

Posted 11 months ago

“The dovetail on the mount is oversized and must be filed down quite a lot to fit. This is the second mount I have installed on my 1911's. Both of them required quite a bit of time to fit. Once installed they seem to be very sturdy. The optics aren't going to move!! Both my 1911"s are .45 ACP. If you do the install yourself be prepared to use a custom file of some sort. I used a Brownells file. It would be nice if the dovetail was a little less oversized. That said I will give it a 4 Star rating! Customer service was very good!!”

Helpful Report

Posted 1 year ago

“My choice of sight for my 1911 A1 was the Primary Arms reflex sight. The location of the pins at the front of the base is too far from the screws that hold it down. The screws with shoulders that were provided were too long by over .100". The Primary Arms sight provides a metal encased area at the rear of the sight to accommodate locating pins. EGW provided no pins or way to accurately locate the sight at the rear. I had to build a set of sleeves and counterbore the base to provide the necessary location and support. I contacted EGW with a request for screws that would work and I offered suggestions. I was rebuffed. The person who responded told me that most customers throw the sleeves into the trash. Interesting reply. What sleeves? You certainly didn't provide any! I asked for shorter screws with shoulders and received a B.S. reply instead. This base is overpriced IMO and I had to rework it. My advice is to buy from some other vendor.”

1 Helpful Report

Posted 1 year ago

“Used a Holosun and pins were already removed”

Helpful Report

Posted 2 years ago

“I mistakenly thought that my 1903 Colt had a GI dovetail cut. I was mistaken. It is smaller, so I'll have to cut it to fit. I intend to mount a SeeAll mk3 open sight, which mounts on a rmrc(compact, not micro). The SeeAll works great with practice. I have used one on a p365, and before that, a S&W Shield. My geezer eyes require a single sight focus point. Thanks, anyway, Raymus”

Helpful Report

Posted 2 years ago

“Awesome mount, perfectly as described and nice and solid and well built it fit my Springfield 1911 A-1 like we used to say “ Like a glove “ nice and tight and it comes with everything to make your red dot go on like it was installed at the manufacturer, no need for a punch I used a sight tool on the Glock side using the 45* just a lil bit of elbow grease and it’s on. Their customer service is really helpful as I had a minor question being my very first sight removal and mount install, will definitely come buy more from EGW just wish I could post a pic of the final install.”

Helpful Report

Posted 3 years ago