Trijicon RMR / SRO, Holosun 407c / 507c Mount for Henry Lever Action, Marlin Lever Action, Ruger PC Carbine Reviews

5 Rating 21 Reviews

Mounting Hardware is Included This Mount Fits:Camp Carbine 9mm (does not fit the early models, the hole spacing is different)Camp Carbine 45Glenfield 30Henry Big Boy (H006)Henry 3030 (H009)Henry 4570 (H010)Henry Big Boy (H012)Henry Long Ranger (H014)Henry .410 (H018) Only fits the 20" BarrelHenry Side Gate Lever Action (H024)Henry Long RangerHenry Homesteader (must use rear holes on receiver)Marlin 1895Marlin 1894Marlin 336Marlin 375Marlin 444Marlin Model 36Ruger PC Carbine**This mount only works with the Ruger PC Carbines that do not have the AR style handguard. Material: 7075 AluminumCoating: Matte Black HardcoatOverall Length: 1.780"Overall Width: 1.1"Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 Set ScrewRed Dot Fitment: Trijicon RMR / SRO, Holosun HE407C / HE507C / HS407C / HS507C, Swampfox Kingslayer / Liberty / Justice Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.Installation Instructions- Remove the rear sight*- Install the EGW Sight Mount- Tighten set screw (if applicable)- Place the red dot sight on the EGW Sight Mount(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)- Apply blue Loctite to the provided mounting screws- Torque mounting screws to 15in/lbs2 Flat Head Cap Screws - Provided for Trijicon RMRThe screws that are included with this mount require a 5/64'' allen wrench for installation.Click here to see a video from Vortex on how to install our red dot base on a slide.
WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH. Modification of your firearm may nullify the manufacturer's warranty.This product should be installed and checked by a qualified gunsmith.No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.

Visit Product Page

Location:

52 BELMONT AVE,
QUAKERTOWN
Pennsylvania
18951

Visit Product Page

“It works. Nice low mount for a red dot without an ugly rail.”

Helpful Report

Posted 1 month ago

“Fit perfectly on the Henry big boy rifle receiver. The holosun HE508T-gr dot is a perfect solution on a lever action rifle. EGW met my expectations,as they always have.”

Helpful Report

Posted 5 months ago

“Perfect fit. Would buy again”

Helpful Report

Posted 6 months ago

“Screws provvided were to long to mount on a henry homesteader”

Helpful Report

Posted 8 months ago

Christopher W

Verified Reviewer

“I haven't installed it yet, but it arrived quickly and well-packaged. I had some questions about it and support was there to assist. Thank you.”

Helpful Report

Posted 9 months ago

“Excellent Holosun mount for the Henry .45 Colt Carbine. The height is perfect for a proper cheek weld.”

Helpful Report

Posted 1 year ago

“I received it in a timely manner. I have a BFR revolver and they don't make a mount specifically for this gun, but I knew the screw holes would line up with the RugerPC mount.with a small trim job on the bottom allowed it to fit perfectly. It cam with 5 sets of screws, but none fit correctly. I then sent a request for som 8-32 headed screws, but they replied that they didn't have that size. They recommended that I go to a local gun Smith to get the screws. They where very good at getting that information to me.”