Trijicon RMR / SRO, Holosun 407c / 507c Mount for Walther PPQ Reviews

4.5 Rating 17 Reviews

Mounting Hardware is Included
This mount fits:
Walther PPQ Classic (M1)
Walther PPQ M2 (All models except optics ready and .22lr)
Walther PPQ 45
Walther PPQ 45 SD
Walther PPQ Sub Compact
Walther P99 (All Models)
Walther PPX (All Models)
Walther Creed
Walther Creed 10 Round
Walther PPS (All Models)
Walther PPS M2 (All Models)
This mount does not fit:
Walther PPQ 22
Walther PPQ Q4 Tac (optics ready)
Walther Q5 Match (optics ready)
Walther P2
Does not work on the PPS and or other Walther models that have the sight rib on top of the slide
Any Walther model that comes with the standard sights that have the detent will work with this mount. This mount now comes with a set screw allowing it to be used with the friction fit dovetails.The PPQ sight has a hole drilled in the bottom of the dovetail to accomodate the plunger on some models of the Walthers.
Material: 7075 AluminumCoating: Matte Black HardcoatOverall Length: 1.780"Overall Width: 1.1"Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set ScrewRed Dot Fitment: Trijicon RMR / SRO, Holosun HE407C / HE507C / HS407C / HS507C, Swampfox Kingslayer / Liberty / Justice
Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.Installation Instructions- Remove the rear sight*- Install the EGW Sight Mount in the dovetail- Tighten set screw (if applicable)- Place the red dot sight on the EGW Sight Mount(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)- Apply blue Loctite to the provided mounting screws- Torque mounting screws to 15in/lbsThe screws that are included with this mount require a 5/64'' allen wrench for installation.
WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH.
Modification of your firearm may nullify the manufacturer's warranty.This product should be installed and checked by a qualified gunsmith.No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.

Alt Description:
Walther PPQ RMR Mount
Walther P99 RMR Mount
Walther PPX RMR Mount
Walther Creed RMR Mount
Walther PPS RMR Mount
Walther PPQ SRO Mount
Walther P99 SRO Mount
Walther PPX SRO Mount
Walther Creed SRO Mount
Walther PPS RMR Mount
Walther PPQ red dot mount
Walther P99 red dot mount
Walther PPX red dot mount
Walther Creed red dot mount
Walther PPS red dot mount

Visit Product Page

Location:

52 BELMONT AVE,
QUAKERTOWN
Pennsylvania
18951

Visit Product Page

“Speedy shipping, perfect fit and installed in seconds. Haven’t shot with it but don’t expect any issues.”

Helpful Report

Posted 1 month ago

“I bought this mount for my P99. It took a bit of filing to get it in the dovetail, but I would rather have to do that than have it be too loose. Now the mount is rock solid. Super stoked with the new red dot setup!”

Helpful Report

Posted 2 months ago

“Love the mount fits perfect with my Trijicon RMR. Just have to get to the range with it to test it out but fit was great”

Helpful Report

Posted 6 months ago

“The customer service correcting my ordering the wrong mount was superb! I did in fact get the correct model. Now to the Mount: It was almost perfect - looking. But it took a LOT of effort to mount it, both to the plate dovetail and the 507C optic posts. It took a bit of sanding on the plate posts to get the optic to finally fit. Then, a LOT(!) of filing on the male dovetail of the plate to get inserted into the .22LR slide. Luckily it was oversized enough to allow for filing. It really did not fit, but I MADE IT FIT. I understand a little bit of the black coating of the aluminum plate needing removal for a snug fit, but this was way too much. It took lots of trial and error, but finally it went far enough in to be centered. I slightly mangled the slide finish from driving it into position. Again: *Superior Customer Service *Superior product finish *Inferior product fitment This may simply be this single gun make (aluminum slide). I am sure others slide right in for different makes. Walther PPQ M2 .22LR? Nope.”

Helpful Report

Posted 7 months ago

“your mount fit like a glove, had no problems installing this mount, simple and easy, mount had the hole for the walther pin and all you do is push it down, cover it, and pops right up. thanks to egw i know have a red dot on my ppq without milling the slide. thank you”

Helpful Report

Posted 1 year ago

“Arrived in a good package right on schedule!”

Helpful Report

Posted 2 years ago

“Fit perfect on my walther ppq and works great. Came with everything except the Allen key fyi”