QU10576 Bend Over Tab Lock Washer for Dodge, IHC, and Jeep Dana 44 Front Axles and IHC Rear Axles with 1-3/4" Spindle Threads fits 1956-1975 International, 1957-1974 Dodge, and 1968-1973 Jeep 4x4 trucks with 1-3/4" hex spindle nuts and external mount wheel hubs. Washer has two pre-bent tabs that fit over the inner spindle nut and 6 bend-over tabs for the outer nut. USA made. Need More Info?
Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project! Dan the Gear Man® Tech Notes: Before Installing
To Install Single Use Part IHC1100 Internal Tab 1.75” Thread Matching Parts Applications
Tech Note 1: Before Installing At least one of the six bend over tabs will line up with a flat on the outer spindle nut after it is tightened. Bend that tab over the outer nut flat to lock the nut in place. Tech Note 2: To Install The pre-bent tabs on QU10576 Washer go over a flat on the inner nut instead of a corner. This may differ from most original lock washers (refer to photo) which have a compound bend on the tabs that will go over a corner of the nut. QU10576 washers are made so the inner tab ends can be altered to grip a nut corner if you require more precise nut adjustment, but if you modify the washer it cannot be returned. Tech Note 3: Single Use Part QU10576 Spindle Lock Washer is designed as a "Single Use" part. For safety reasons, these parts are intended to be installed once and only once! The key slot tab, which keeps the washer from turning, can become fatigued and break off if the washer is reused or if the outer nut is over torqued. You must discard any QU40037 lock washer that is removed from the spindle for any reason and replace it with a new QU10576 Spindle Lock Washer. Tech Note 4: IHC 1100 This Lock Washer fits 1957-1974 Dodge, 1956-1975 International, and 1968-1973 Jeep trucks with front spindles that have 1-3/4' threads and wheel hubs that are drilled and tapped with 6 3/8" holes in a 3-3/4" bolt circle to mount an external drive flange or lockout hub. QU10576 washer is NOT used on 1964-1975 International 1/2 ton 4x4s or 1969-1974 Dodge W-100 4x4 trucks with 3-3/8" diameter internally splined wheel hubs. If you are looking for spindle lock washers for a IHC 1100 or Dodge W-100 with internally splined hubs see QU40060 Washer or QK4727 Spindle Nut Set. Tech Note 5: Internal Tab QU10576 Spindle Lock Washer has an internal tab that fits a 1/4" spindle key slot. It is not uncommon to find a spindle with slightly mashed threads at the outboard end which will reduce the slot width. If present, this condition will need to be fixed before you can install the lock washer. Tech Note 6: 1.750” Thread International and Jeep truck year and model application information is often difficult to precisely list due to the relatively low production numbers and the fact that both manufacturers often built special purpose vehicles for government and vocational applications. Regardless of the application information, if you have a front spindle with 1.750" thread, QU10576 is the correct part for your 4x4. Tech Note 7: Matching Parts QU11164 Hex Spindle Nut with 1-3/4" ThreadQU11165 Spindle Thrust Washer (goes between outer wheel bearing and inner spindle nut)TK40573 Gasket for Lockout Hub or Drive FlangeQU50704 Front Wheel SealQU50701 Wheel Bearing CupQU50702 Wheel Bearing 1-3/4" IDQU50703 Wheel Bearing 1-13/16" ID TK4924 Front Wheel Bearing Kit 1957-1968 Dodge and 1956-1971.5 IHCTK4926 Front Wheel Bearing Kit 1969-1974 Dodge, IHC, and 1968-1973 JeepQT1013i 2-1/2" Hex Spindle Nut SocketDodge & Ram Shop ManualsJeep Shop Manuals Applications:
Dodge: W100: 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968
W200: 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974 International: 100, 1100 1/2 ton with 6 bolt, external mount hub with 3-3/4" bolt circle: 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963 120, 1200, 1210 3/4 ton: 1956, 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975
Dana 60 Rear Axle: 1966, 1967, 1968, 1969, 1970, 1971, 1972, 1973, 1974, 1975 Jeep: J4000 with 8000 pound GVW including Camper Special: 1968, 1969, 1970 J4800 with 8000 pound GVW including Camper Special: 1971, 1972, 1973
Phone:
406-384-0270
Email:
sales@torqueking.com
Location:
7727 S Leopard Ave,
Billings
Montana
59106
