QU10233U Used BARE 1999-2007 GM NV4500 4x2 C-Truck Rear Housing for 1999-2007 C2500, and C3500 Chevy Silverado and GMC Sierra trucks with fixed output yoke and a screw-in speedometer sensor. Available while supplies last.
Also See: QU10233 New C-Truck Rear Housing
Need More Info?
Use the handy Links below to access over 40 years of Dan's product and vehicle specific Tech Notes to easily get the information you need for your vehicle's repair, maintenance, or upgrade project!
Dan the Gear Man® Tech Notes: Product Note
Housing Specs Speedometer Sensors Sealants NV4500 Tools Rear Output Applications Matching Parts Applications
Tech Note 1: Product NoteSince these housings are from used transmissions, there will be some RTV sealant you will need to clean off the mating surfaces.
Tech Note 2: Housing SpecsQU10233U GM NV4500 Tailshaft housing is approximately 6-3/8"” long. The casting number is 25868. The bolt pattern on the front is the universal NV4500 8 bolt main case to rear housing pattern. The rear of the housing will need QU50155 output shaft support bearing, QU10319 Bearing Snap Ring, and QU10720 rear output seal.
Tech Note 3: Speedometer Sensors4x2 GM NV4500 transmissions in C-Series trucks were built with two types of Speedometer Sensors. QU10227 Bolt-In or Push-In type speedometer Sensor first appeared in 1992 and it was used until early 2002 in C-Series GM trucks with the GMT400 body. The Speedometer Sensor is grooved for an o-ring and it is installed by pushing it into a smooth hole in the rear output housing. The sensor has an integeral metal tab that is secured to the tailshaft housing with a bolt.
For the 1999 model year, GM introduced the C-Series, GMT800 body style and it was offered until 2007 with a NV4500 tailshaft housing that uses QU10228 Screw-In Speedometer Sensor. QU10233 is made to work with the screw-in speedometer sensor.
Tech Note 4: SealantsEarly production NV4500 Transmissions used an anaerobic sealant (QU90003) to seal between the main case and input bearing retainer, top cover, and rear housing. Mid-production units used anaerobic sealant just on the input retainer and RTV for everything else. Later production transmissions used black RTV sealant (QU90006 or QU90005) for everything. Either type of sealant works fine (except the PTO covers ALWAYS should be sealed with RTV), but I prefer RTV for all components. Regardless of which sealant you use, make sure excess sealant does not block the lube access hole at the top of input retainer pilot that fits into the transmission case. Also, the threaded holes in the main case for the four retainer bolts and 12 PTO bolts are open ended, so you must use new bolts with factory applied theadlocker or apply Threadlocker (S24200) to your existing bolts to prevent oil seepage past the bolt threads. See my TM1003 NV4500 Shop Manual or VSG1003DVD NV4500 Overhaul Video for more information.
Tech Note 5: NV4500 ToolsNeed Torque Specs or Rebuild procedures? Order my 116 page, full color illustrated TM1003 NV4500 Rebuild Manual. You will need some special tools to correctly service your NV4500 Transmission. The chart below lists our current NV4500 Special Tools for popular models.
TOOLS for SPECIFIC NV4500 MODELS
Component
23 SplineDodge 4x4NV4500LD
29 SplineDodge 4x4NV4500HD
30 SplineDodge 4x2NV4500LD
31 SplineDodge 4x2NV4500HD
32 SplineGM 4x4
35 SplineGM 4x2
Mainshaft Nut
QT2002
QT2001QT2036
QT2002
QT2001QT2036
QT2002QT2028
1-1/2" HexSocket
Mainshaft Holding
NLA
QT2000
NLA
QT2011
N/A
N/A
5th Gear NutTorx® Cross Bolt
N/A
QT9205
N/A
QT9205
N/A
N/A
Output Seal Installer
N/A
QT1801
N/A
QT2058CALL
Not Used
Not Used
Tailshaft Bushing Remover and Installer
Not Used
Not Used
Not Used
QT2044
Not Used
Not Used
TOOLS For ALL NV4500 MODELS
CountershaftFront Bearing Cup Installer
QT1802
Use with QT1101 or QT1119 Driver Handle. Also can use flat side to install Dodge 4x4 Rear Output Seal
Countershaft Front Bearing Installer
QT2004
Can also use to press 3-4 Synchro Hub on original equipment mainshafts
Input Bearing & Countershaft Rear Bearing Installer
QT2005
Can also use to install Input Seal
Input Bearing Cup Installer
QT1801
Use with QT1100, QT1101, QT1116, or QT1119 Driver Handle.
Countershaft Support
QT2006
Use to support front of countersahft when installing countershaft rear bearing
1-2 Synchronizer Support
QT2008
Use to support 1-2 synchronizer hub during synchronizer assembly
10mm 1/2" Drive 12 Point Socket
QT1020
USA Made Impact Socket for Factory Tailshaft Housing Bolts
Long Shank Punch for Shift Lug
QT9300
3/16" x 8" Shank for 5th Gear Shift Lug Roll Pin
Tech Note 6: Rear Output ApplicationsNV4500 Transmissions are frequently used for conversion applications. The Table below lists the most popular rear output applications and their associated parts.
Component
23 SplineDodge 4x4
29 SplineDodge 4x4
31 SplineDodge 4x2w/Speedo
31 SplineDodge 4x2No Speedo
32 SplineGM 4x4
35 SplineGM 4x2Short*
35 SplineGM 4x2Long*
Mainshaft
QU10214
QA1045 orQU10011
QU10013
QU10013
QU10098
QU10719
QU10212
Rear Housing
QU10057U
QU10057U
QU10024
QU10083
QU10716
QU10233
QU10217
5th Gear**
QU10007QU10086
QU10067
QU10067
QU10067
QU10007QU10086
QU10007QU10086
QU10007QU10086
5th GearNut Set
QK1093QU10097
QU10069
QU10069
QU10069
QK1093QU10097
See YokeNut
See YokeNut
SpeedometerDrive
Not Used
Not Used
QU10027QK1143
Not Used
Not Used
QU10177
QU10177
SpeedometerSnap Ring
Not Used
Not Used
QU10330QK1143
Not Used
Not Used
Not Used
Not Used
SpeedometerSender
Not Used
Not Used
ContactDealer
Not Used
Not Used
QU10228
QU10228
SpeedometerO-Ring
Not Used
Not Used
QU10678
Not Used
Not Used
incl. withQU10228
incl. withQU10228
Spacer
Not Used
Not Used
Not Used
Not Used
QU10172QU10173
Not Used
QU10738
Bushing orBearing
Not Used
Not Used
QU10025
QU10025
Not Used
QU50155
QU50155
BearingSnap Ring
Not Used
Not Used
Not Used
Not Used
Not Used
QU10319
QU10319
Output Seal
QU10123
QU10123
QU10023
QU10023
Not Used
QU10720
QU50204
Gasket
TK10519
TK10519
Not Used
Not Used
TK30052
Not Used
Not Used
Yoke
Not Used
Not Used
QU40700QU40354QU40495
QU40700QU40354QU40495
Not Used
QU10184QU10727QU30094
QU40902
Yoke Spline Seal
Not Used
Not Used
QU10026
QU10026
Not Used
QU30009
QU30009
Yoke Washer
Not Used
Not Used
Not Used
Not Used
Not Used
QU30095
QU30095
Yoke Nut
See 5thGear Nut
See 5thgear Nut
See 5thGear Nut
See 5thGear Nut
See 5thGear Nut
QU10181
QU10181
*Electronic, Screw-In Speedometer Sensor**22 Tooth Mainshaft 5th Gears listed for 1992-2005 Dodge and 1995-2007 GM with 5.61:1 1st gear ratio. 1992-1994 GM with 6.34:1 first gear ratio use 19 Tooth QU10728 Gear. QU10728 is NOT compatible with Dodge 29 and 31 Spline Output Shafts.
Tech Note 7: Matching PartsMatching Parts for QU10233U GM NV4500 4x2 Rear Housing:QU10106 12 Point Metric Tailshaft Housing Bolt with factory applied ThreadlockerQU10146 Tailshaft Housing Alignment DowellNV4500L Transmission Main Case for 1997-2007 GMQU10184 1350 Series Rear Output YokeQU10727 1350 Series Rear Output Yoke with DampenerQU30094 1410 Series Rear Output YokeQU10184 1410 Series Rear Output Yoke with DampenerQU10228 Screw-In Speedometer SensorQU90003 Anerobic SealantQU90006 3.35 oz Ultra Black RTV SealantQU90005 0.5 oz Ultra Black RTV SealantS24200 6ml ThreadlockerS9978 1 gram ThreadlockerQU90020 NV4500 Manual Transmission OilTM1003 NV4500 Shop ManualVSG1003DVD NV4500 Overhaul VideoChevy & GMC Shop Manuals
Applications
Chevy and GMC:C2500, C3500 series Silverado and Sierra GMT800 Body Style: 1999, 2000, 2001, 2002C2500, C3500 series Silverado and Sierra: 2003, 2004, 2005, 2006C2500 series Silverado Classic and Sierra Classic: 2007
Phone:
406-384-0270
Email:
sales@torqueking.com
Location:
7727 S Leopard Ave,
Billings
Montana
59106
