Pioneer GM-D9701 Mono Block 2400W Class D amplifier with bass remote Reviews

4.5 Rating 11 Reviews

Visit Product Page

Phone:

0330 320 5050

Email:

sales@caraudiocentre.co.uk

Location:

29 Bridlesmith Gate,
Nottingham
Nottinghamshire
NG1 2GR

Visit Product Page

“Great little amp, running very well with plenty of good bass. I did have the inphase one which is recommended first, which spent most of the time of ownership in the shop getting repaired opted for this as a replacement, much happier now”

Helpful Report

Posted 2 years ago

“I'm currently running this amp to power a Pioneer TS-D12D2 12" Dual 2 Ohm Voice Coil Subwoofer. I must say that I am quite happy. I've currently got the sub wired up as a 4ohm load. I set the gain using my oscilloscope with a 50hz signal. I have also tried wiring the sub as a 1ohm load, and although it was obviously able to get it a litre louder (limited by a 600w rms sub) I found the sound wasn't as clean as in a 4ohm configuration. I also borrowed my friend's sub (same as mine) and wired the 2 subs up as a 2ohm load. Although my van was certainly shaking, this amp is a was a little under powered for both subs. The amp with a 2ohm load can only produce 800w rms which is 400w under the 2 subs total of 1200w rms, I think this is where people my have been feeling a little let down. I have had no over heating issues in any of the wiring configurations and have had the amp running full volume for a full 30 minutes. The amp is also mounted upside-down to the roof of my van. From my experience with this amp, I would say make sure to match it up with a correct rms sub (and this will depend on the wiring configuration/load). I would probably say, keep things within 100w of the rms, e.g. 4ohm 400-600w rms sub. 20hm load 700-900w rms sub or 2 subs to that total. 1ohm load 1100-1300w sub or 2 subs to that total. I will eventually be using this amp to power 3 x 350w rms 4ohm single voice coils shallow subs wired in parallel for a 1.33ohm load. If I have any issues I will update the review. My crosser is set as follows. Sub up to 80hz 12db slope Mids 90 to 2.5khz 6db slope Twitter 4khz 12db slope I hope someone finds the above info useful.”

Helpful Report

Posted 2 years ago

“Returned after 7 days. Because the low end was crap. I though it was a faulty amp so I got a replacement. Replacement sounds just as crap. Returning for a refund. Will buy the IPA2001D on payday”

Helpful Report

Posted 3 years ago

“The inphase amp deal with kenwood sub, would the amp run in bridge mode? Or is a better 1 ch amp on offer. Looking to buy online but need good deal. Already run 0 guage from battery and power gain switch and quality rca leads.”

Helpful Report

Posted 4 years ago

“I have this running 2 x Vide black air 122 and it really struggles, thelow end it bottoms out and I dont think the power it quotes is correct. Not reconemdnend”

Helpful Report

Posted 4 years ago

“This little gem was recommended to me by ilford branch for my twin alpine setup. Cannot believe the price of it for that sort of power. Glad i visited your ilford branch, cause another shop suggested different make amplifier for double the price. you have a great team at your ilford branch.”

Helpful Report

Posted 4 years ago

“RECIVED THE AMPLIFIER . HAPPY BECAUSE ITS 100% ORIGINAL PRODUCT. 0RDER NO CA.........”

Helpful Report

Posted 4 years ago

“great amp for the price can deliver some serious bass got mine hooked up to twin Kenwood KFC WPS 1200f subs (350w RMS each) (running them in parelell at 2 ohms the amp can kick out 800 RMS at 2 ohms) love that it comes with a bass controller a good quality one too”

Helpful Report

Posted 4 years ago